Since we last checked in with our caped crusaders, aka the bathroom bandits, aka my Dad and our friend, LOTS has been movin' and shakin' at Ms. H's house. It's a tale of plumbing, subfloor replacement, cement board installation and built-in planning. There's drama. There's comedy. But mostly there's just work and progress, which is the way it's supposed to be. And in this post, I also have some handy *tips* sprinkled throughout!
If you missed the earlier posts, this is what we started with:
After taking all the tile off, removing the old vanity, and getting down to the studs in the shower surround, my Dad and our friend Keith soldered new pipes in place for the tub and shower. They also had to install new 1/2" Hardiebacker cement board which will allow us to put fresh tile on the shower walls.
And here's your first *tip*: If you're cutting a large board like this, lay 2x4's underneath the board, on top of your sawhorses. Then, cut right down the middle of them and you won't accidentally cut anything underneath. - My Dad says to help support the weight of a large board while it's being cut, he would also sometimes put another layer of 2x4's across the first layer. Think Lincoln Logs...
Dad did the cutting with my new Ryobi circular saw (woot woot!) which worked like a charm.
In order to complete hanging the cement board around the shower, we had to add a few 2x4's to give the boards a secure place to be screwed into. Time for me to step up and use my own saw!
Here's your second *tip*: If you have to add reinforcements to existing studs, err on the side of cutting the support piece a smidge too big rather than a smidge too small.
I was worried I'd cut it too big at first, but my Dad encouraged me to pound it in place. Man, it was snug. Dad said, it's better that it be a snug fit than too small - because then you end up having to brace it, or start all over with another piece of wood.
And here's our hole where the old medicine cabinet was.
To the right is where I sketched in the location for the new recessed shelves. I used a level to make sure everything was precise.
I had to make sure we were building them around the existing vent pipe in the wall, so I drilled small holes where I thought the edges of the pipe were. I didn't drill deep enough to hit the pipe. But the holes weren't big enough to see through. So I had to devise another way to identify where exactly the edges of the pipe were.
I used a leftover piece of insulated wire to stick through the holes. It was firm enough that it didn't crumple when I poked it through. I could clearly feel when I hit the pipe and when I didn't. Mission accomplished!
Cement board nearly done on the shower, we attacked the floor.
Scraped up old linoleum.
Measured for the new subfloor.
Dad taught me how to lay 1/4" Hardiebacker on the floor.
The Ryobi saw cut out the notches for the vent perfectly. Dad was careful not to notch in too far... it worked great.
Here's your next *tip*!
Before we went and mixed up the mortar for the new subfloor pieces, we grabbed the vent cover and made sure it fit :-) Not that this has ever happened to my Dad before... he may in fact just be that smart.
And for my next *tip* -
this rectangle was the last bit of floor we needed to cut a piece to fit. I would have just measured the length once and the width once. Dad, again, Professor Smarty Pants (he does have an actual PhD) told me that especially with a corner piece like this, you should measure the length at one end AND the other end, and the width at one end AND the other end because HELLO - corners in houses are not always 90 degrees! He was right. One end was different than the other by 1/4"
Then I strapped on my knee pads and learned how to spread mortar on the floor. A lot like icing a cake. The pieces went into place perfectly and now we have a fantastic new subfloor that will ensure the new tile floor we lay will last.
This picture is somewhere.......
Next up is to frame in the recessed shelving above the toilet. Since that wall is where all the plumbing in the room is (contractors might call it a wet wall), there is extra space in between the wall in the bath and the room on the other side of the studs. If you can, TAKE ADVANTAGE of this space! It is prime real estate! You too, may have spaces, all covered up and unused that could be put to work in your own home. It may not seem like a big deal, to have a few square feet to tuck away small items. But in a bath like this - the only bath in this home - every inch needs to be maximized.
Again, here is what we're sort of going for:
We picked up the mirrored medicine cabinet at Home Depot, a frameless, beveled mirror that will be recessed into the "wet" wall above the sink. Keith held it up so Ms. H would be sure to sign off on the height where it's placed.
Two sets of shelves will be built in to the right of that.
This is not the first built-in I've planned in a home. But it will be the first one I help build and execute myself - and for someone else's home. So a little nerve-wracking. But mostly just exciting!
Yes, Ms. H could put a storage tower back over the toilet, and it would work fine. But, if all goes as planned, we'll add some quality storage - and a bit of character and architecture - to this small room.
That's an investment I can get behind!
In case I haven't convinced you yet that I'm obsessed with built-ins, here's my
Pinterest board to
drool over prove it. Have a look. If you're not dying to suddenly call a carpenter, we need to talk!
Thank you so much for reading!!
XO,
Anne
